Celaschi TSA 280/DS TENONERS

- 1st OR 2nd MACHINE IN LINE
High performance machine.
Robust structure in welded and stressed steel, sized according to the machine configuration and length.
Fixed left hand side - right hand side movable twice as long ground steel guides, with automatic lubrication.
Positioning control is also possible with the remote control card.
Safety relay to prevent the mobile side from starting while chain-track is running and to prevent the track from working while the movable side is positioned.
The joint pins, made of hardened steel, 16 mm in diameter, slide
Dust-tight and lubricated-for-life bearings.
Dogs pop up every 400mm apart
Chain track liner panels are made of high strength vulcanized rubber on steel plates.
The steel support plate is 2mm thick and is attached to the top of the chain link using 4 screws.
The balanced drive shaft (80 mm diameter) has a large positive keyway and guide spool
The sprockets are hardened at the contact points.
Upper pressure beams have a single V-belt with clutch.
Steel covers for supply and outlet for chain protection.
The columns that support the work units and sled/slide supports
They are made of solid cast iron with precision dovetail guides.
Centralized lubrication system for all sliding surfaces of the saddle-slide.
All operating units are tiltable 0-90 degrees.
All vertical/horizontal adjustment motors with Siko readings
Electrical cabinet supplied with standard 3 m connection cables.
Emergency stop cable on the back, shim safety on the top
Pressure rays and stop button on the control panel.
Safety photocells on the front

CELASCHI TSA 280 - 380V / 3PH / 50 hz - front chain extension 1100 mm
- WORKING WIDTH 220 - 3,000 MM
- THICKNESS OF THE PIECE 8-80 MM
- TOP PRESSURE BEAMS WITH TRANSMISSION AND CLUTCH BELTS
- POWER CHAIN AT THE BOTTOM MM. 80 WITH BEARINGS
- AUTOMATIC LUBRICATION OF BEDS
- AUTOMATIC LUBRICATION OF THE POWER CHAIN
- POP UP DOGS DISTANCE 400 MM
- VARIABLE FEED SPEED 4-24 MT/MIN
- ELECTRONIC OPENING OF THE CABINET SIDE WITH 2-SPEED MOTOR (FAST SLOW)
- ELECTRONIC LIFTING OF BEAMS AT HIGHER PRESSURE
- MANUALS AND ELECTRICAL DIAGRAMS
- SEPARATE CONTROL CABINET
- VOLT 380V / 3ph / 50 hertz

MACHINE EQUIPPED WITH:
- LH ADJUSTABLE SWIVELING SIDE FENCE - MANUAL HORIZONTAL ADJUSTMENT
1-2 CUTTING/SCORING JUMP UNITS attached to hoggers
- 1.6 KW (2.2HP) MOTORS - 6000 RPM BY INVERTER
- 0-190 degrees tiltable
- shafts diam 25 X 28 L - max tool diam 150 - DUST OUTLET DIA 80mm
3-4 HOGGING - 5.5 / 8 HP - 6000 RPM
- SHAFTS DIA 35x63 - Max tool diam 250mm
- DUST OUTLET DIAM 120mm
- 0-190 degrees tiltable
5-6 SKIP MILLING UNIT
- WITH PNEUMATIC JUMP IN / OUT
- HEAVY DUTY ENGINES 10 HP - 6000 RPM
- MOTORS IN VERTICAL POSITION
- SHAFTS DIA 40 x 240 - Max tool diameter 250mm
-DUST OUTLET DIA 140mm
7-8 MILLING UNIT
- HEAVY DUTY ENGINES 10 HP - 6000 RPM
- MOTORS IN VERTICAL POSITION
- SHAFTS DIA 40 x 240 - Max tool diameter 250mm - DUST OUTLET DIA 140mm
- DUST AND ACOUSTIC CABINETS
- MOTORS DRIVEN BY STATIC INVERTER
- MAIN DRIVE MOTOR - ADJUSTABLE SPEED BY INVERTER
- PLC CONTROL FOR THE SELECTION OF WORKING UNITS
- ELECTRONIC HEIGHT ADJUSTMENT (THICKNESS)
- ELECTRONIC WIDTH ADJUSTMENT, PROGRAMMABLE
- DUST AND ACOUSTIC CABINETS