Weinig Unipin 200

Unipin 200 with parapet gluing
Dowel driving machine with automatic gluing
! Sold on behalf of a customer: Only around 40 operating hours, no longer required due to product changeover!

Manufacturer description:
Weinig UniPin 200 for driving in dowels on the front after automatic glue application
Workpiece clamping pneumatically via hand switch after manual presetting (handwheel).
Room conditions

Temperature:
In operation: from 15 to 30°C
Out of operation: from 15 to 30°C
During storage and before installation: from 5 to 40°C - +/- 5%
Relative humidity (without condensation):
In operation: from 10 to 70% - +/- 10%
Out of operation: from 10 to 70% - +/- 10%
During storage and before installation: from 0 to 90% - +/- 5%
Altitude
In operation: from 0 - 1500 m above sea level

Technical data:
Total connected load approx. 1.5 KW (2.0 HP)
Full load current: approx. 3 A
Pre-fuse: max. 10 A
Air consumption/standard: 80 l/min
Blow-out device: 150 l/min
Operating pressure: supply 8 bar
Operating pressure: UniPin 6 bar
Permissible workpiece dimensions:
Width: 260 mm
Height: 150 mm
Dimensions
Base area: 1050 x 2150 mm
Working height: approx. 1000 mm
Permissible dowel dimensions according to DIN 68150
Diameter 8 mm +/- 0.2 mm
Length 60 mm +/- 1 mm
Dowel feed via vibration conveyor
Dowel diameter: 8 mm
Filling quantity: 500 pieces
Pressing force: max. 1000 N

Glue system:
Standard container: 30 liters
Glue pressure: up to max. 50 bar
For processing B4/D4 glue, one-component
according to DIN 68602 / EN 204 suitable.
Pump control system made entirely of V4A steel
Viscosity at 25°C < 5000 m Pascal
Viscosity at 20°C < 4000 m Pascal

Standard equipment:
Electronic dowel driving depth monitoring
The driving depth of the dowel is indirectly monitored electronically via the end position of the driving cylinder.
If the end position of the driving bolt is not reached during driving,
the machine is stopped and a message is displayed on the operating terminal.
Prerequisites:
- Part must lie cleanly on the zero edge.
- Dowel must correspond to the preset length
Electronic glue monitoring consisting of monitoring the nozzle needle and pressure difference at the glue nozzle.
Advantage:
Ensures the gluing function
The machine is stopped if there is a malfunction in the gluing function
and a message is displayed on the operating terminal.
The customer is responsible for maintaining the quality of the corner strength of the corner connection.
Weinig accepts no liability for compliance with the quality standards of the corner connection

Parapet gluing:
Contactless application of glue dots to the front of the workpiece with a pulse valve.
The dot size can be set by the nozzle opening time and or by means of the glue pressure.
The rows of dots must be transferred from the customer’s computer program.
The first and last dots in the respective horizontal line are described.
The distances between the glue dots are calculated automatically by the control system.
Optionally, a maximum dot distance can be transferred in the data set.
The customer provides the industry software.
The customer is responsible for any necessary adjustments to the industry software.

Counter-hole gluing:
Hand gun for counter-hole gluing including 6.0 m hose line,
with solenoid valve for controlling the amount of glue.
The pulse time can be set on the operating terminal.
The glue gun can also be used in continuous operation.

Swivel boom (3.0 m) to hold the hand gun, including hose guide and spring balancer for ergonomic handling
Height of the hand gun from the top edge of the floor: 1400 mm
Height of the swivel boom from the top edge of the floor: 2500 - 3000 mm
Swivel radius: 3000 mm

Double part processing for efficient processing of two parts at the same time.
Three additional stop cylinders can be selected manually.
Workpiece dimensions for double part processing
Wood width max. 110 mm
Wood height max. 150 mm

Machine electrics:
Operating voltage 400/415 volts
(voltage range 380 - 420 volts), 50/60 hertz
Electrical design according to DIN VDE 0113, electrical equipment of industrial machines EN60204, IEC-204-1.
Other electrical regulations are not taken into account.
When using frequency-controlled drives in our machines, it is not possible to operate them on residual current devices (RCDs).
On the building side, the power supply line to our control cabinet must be earth- and short-circuit-proof
(e.g. by using single-core NYY cables or a correspondingly mechanically protected installation).
The operation of the machine without a residual current device must
be reported to the property insurer; accompanying technical measures may be required.
See also VDMA position paper: Use of electrical equipment of machines according to DIN EN 60204-1
(VDE 0113-1):2007-06 in fire-hazardous operating facilities according to DIN VDE 0100-482 (VDE 0100-482):2003-06
Announcement of DKE/K 225 and DKE/UK 221.2
The respective country-specific regulations must be observed and complied with

Machine operation:
The machine is operated using a computer on the screen.
Convenient operator guidance and online help in dialogue.

Control
Industrial PC with Weinig user interface:
- easy networking option for data transfer based on Windows
- Best possible operator support through modern, graphical user interface
- Remote diagnosis via Internet (VPN) or telephone connection, these must be provided by the client.
- Network card (10/100 Megabit/TCP/IP), RJ 45
- Touchscreen

Control functions:
- Position-by-position processing of production orders with graphic display on the touchscreen
- Parts tipping (support side)

Interface for online connection to the Conturex:
The control uses the same data set as the Conturex, in that it contains all dowel positions.
When importing the data set into the user interface, all parts are filtered for face dowels and processed in the same production sequence as with the Conturex

Interface for external online connection
The industry software transfers part information such as dimensions and profile.
The dowel positions (X/Y/Z) are also transferred as individual processing.
The industry software is provided by the client.
The client is responsible for any necessary adjustments to the industry software.