Schuler BZE 2000-45/26.5.1 2000 tons

SCHULER BZE 2000-45/26.5.1
Year 2011

Tonnage 2000 tons
Stroke 1750 millimeters
Equipped With
Principle of Action: Hydraulic Triple Action Head Press, D/A (S/A possible)
Slide Capacity: 20,000 kN (coupled)
Clamping Area: 4,500mm x 2,500mm (coupled)
Lateral Window in the Upright: 2,580mm
Slide Stroke: 1,750mm
Height of Smallest Die: 1,050mm
Slide TDC Max: 2,800mm
Tool Clamps on Slide: 18 x Hilma Hollow piston cylinder
Tool Weight: 25 to upper tool-25 to lower tool
Bed Cushion Capacity: 6,000 kN
Bed Cushion Stroke (total): 320mm
Bed Cushion Area: 3,600mm x 1,800mm
Bed Cushion Grid Pattern: Offset grid pattern 100mm bolt diameter 58/50
Bed Cushion Multi-Point Control: 8 point
Press Control: Beckhoff PC Control
Ram Speed: down 750mm/s, up 550 mm/s
Height of Press: 8.8m

Hydraulic Triple-Action Head Press Type BZE 2000-45/26.5.1
Total Ram Force: single action mode: 20,000 kN, 3 Cylinders: 12,000 kN, 2 Cylinders: 8,000 kN
Upper Blank Holder Force: (4 x 2,000 kN) 8,000 kN
Ram Stroke: 1,750mm
Upper Blank Holder Force: 1,250 + 500 mm
Distance Between Moving Bolster and Ram: Stroke Up: 2,800mm Stroke Down: 1,050mm
Table Size + Upper Blank Holder Size: 4,500 x 2,500 mm
Ram Size: 3,650 x 1,650 mm
Distance Between Uprights: approx. 4,530mm
Lateral Opening in the Uprights: Height above moving bolster approx. 2,500mm Width: 2,600mm
Moving Bolster Height above floor: approx. 550mm
Total Height above floor: approx. 8,900mm
Installed Capacity for main drive: 3 x 200 = 600kW
Total Capacity Installed: approx. 735 kW
Ram Speeds: Fast Downward speed approx. 750mm/s Return SPeed approx. 55 mm/s
With 2 Ram Cylinders (Triple Action and Single-Action mode)
Working Speed max. up to 2,600 kN approx. 168 mm/s
Working speed max. at 8,000 kN approx 52 mm/s
With 3 ram Cylinders (Triple Action and Single Action mode):
Working speed max. up to 4,000kN approx 112 mm/s
Working speed max at 12,000 kN approx 36 mm/s
With 3 ram Cylinders and 4 blankholder cyl (Single Action mode only)
Working speed max up to 6,000 kN approx 68 mm/s
Working speed max at 20,000 kN approx 22 mm/s
The return speed is calculated with a max upper die weight of 17.5 to
Die height (closed) max 1,600 mm
(according to Stola's information) min 1,050mm
1 Hydraulic 8 point drawing cushion in the press bed
Drawing Cushion force )8 x 750 kN) 6,000 kN
Drawing Cushion Stroke: 320 mm
Size of Drawing Cushion Table: 3,680 x 2,030 mm
Distance of pin rows has to be discussed
Diameter of cushion pins has to be discussed
2 Moving bolsters exit to left / right
Bolster Size: 4,500 x 2,500 mm
Height of the bolsters above floor: 550 mm
Traveling Speed: approx 1.5 6 m/min
Admissible load approx. 50 ton