Illig RDKP 72k

Forming area with actuated clamping frame max. 676 x 535mm
Forming area without/with spring-mounted clamp.
frame max. 756 x535mm
Tool width between material transport with pneum.
clamping frame max./min. 700 /450mm
Tool width between material transport without/with
spring-mounted clamping frame max./min. 780/450mm
Tool length in indexing direction max./min. 565/270mm
Tool height at upper table max. 170mm
Tool height at lower table max. 170mm
Material width with actuated clamping frame max./min. 725/475mm
Material width without spring-mounted clamping frame max./min. 805/475mm
Material width at discharge side max. 845mm
Spreading dimension per side max. 20mm
Material thickness max. (subject to type of material) 2.5mm
Material thickness min. (subject to type of material) 0.18mm
Accuracy of material transport (measured at skeletal bridge)
± 0.2mm
Index length max./min 553/258mm
Height of formed part above material level max. 120mm
Height of formed part below material level max. 120mm
Total height of formed part max. 120mm
Table stroke on top max./min. 140/50mm
Table stroke on bottom max./min. 140/50mm
Length of upper heater 1750mm
Length of lower heater 1750mm
Carrying capacity of vacuum pumps (Series/[Option])
max. 140m³/h
Mold closing force max. 200kN
Forming pressure max. 5bar
Heat to be dissipated on upper and
lower heater max. 75000kJ/h
Cooling water connection on machine 1"
Cooling water connection tool cooling circuit 1"
Cooling water connection material transport 0.5"
Cooling water connection machine recommended 20°C
Cooling water connection tool recommended 15°C
Cooling water pressure 4 - 6 bar
Compressed air connection on machine 1.5"
Compressed air tank 100L
Operating pressure 6 - 10bar
Supply pressure recommended 8bar
Number of cycles max. 40 1/min
Number of cycles with process optimisation max. 55 1/min
Number of cycles min. 5 1/min
Material level above ground approx. Total length without material roll stand 1150mm

Connected loads
Upper heater 37.1 kW
Lower heater 37.1 kW
Upper heater (Option) [38.4 kW]
Lower heater (Option)[38.4 kW]
Vacuum pump 3.0 kW
Forming machine 4kW
Servo-drive for upper and lower clamping frame 1kW
Total connected load (Option) 81.2 kW
Individual air requirement per working cycle at
6 bar supply pressure
Average forming air at 5 bar forming pressure approx. 210 NL/cycle
Clamping frame, pneumatically 50 NL/cycle
Demoulding air approx. 15 NL/cycle
Total air consumption per working cycle approx. 275 NL/cycle

Hole punch
Number of cycles max. 55 1/min
Punching force max. 600 kN
Height adj. upp. table adjustment value 0.1 mm/cycle
Tool width between material transport max. 780mm
Tool length in operating direction max. 580mm
Tool height on upper table max./min. 120 - 220mm
Tool height on low er table max./min. 110 - 200mm
Punching level above material level max. 120mm
Punching level below material level max. 120mm
Table stroke on top max. 140mm
Table stroke on bottom max. 140mm

Steel Rule Punch
Number of cycles max. 55 1/min
Punching force max. 600kN
Height adj. upp. table, value of adjustment 0.03mm
Tool width between material transport max. 780mm
Tool length in indexing direction max. 555mm
Punching dimension in indexing direction max. 550mm
Punching dimension across indexing direction 775mm
Tool height on upper table max./min. 140/80mm
Tool height on lower table max./min. 140/4mm
Height of punching part above material level max. 120mm