Georg 41" x 6.30" x 15,000 Slitting Line

Georg 41" x 6.30" x 15,000
Year built: 1979

Model: KS160/250-1000W
Materials: GO, GNO, Copper, Alum.
Min./Max. Coil Width: 2 - 41" (Trimmed)
Thickness Range: 0.006" - 0.018" (GO/GNO)
0.005" - 0.100" (Copper, Alum.)
Width Tolerance: +/- 0.001"
Max. Shear: 14,000 PSI (Alum.)
23,000 PSI (GO/GNO)
81,000 PSI (GO/GNO)
Max. Coil Weight (Entry): 15,000#
Max. Coil Weight (Exit): 6,000# @ 8" Dia. Drum
15,000# @ 24" Dia. Drum
Coil I.D. (Entry): 16" - 19" / 19" - 22" with Risers
22" - 24.5" with Risers
Coil I.D. (Exit): 8" & 24"
Max. Coil O.D.: 55"
Line Direction: Right to Left
Mode of Operation: Pull Thru / Driven
Line Speed: 0 - 660 FPM (GO/GNO)
0 - 260 FPM (Alum./Copper)

Consisting of the following:
-Entry Coil Storage Saddle:
Two (2) Full Width Coils

-Entry Coil Car:
Pit Type
Powered Lift and Traverse

-Uncoiler:
Single Mandrel Type
Hydraulic Expansion
Sliding Base
33.5 HP DC Motor Driven
Holddown with Powered Snubber Roll
Two (2) Sets of Bolt-On Risers (not confirmed)

-Automatic Edge Guide:
Photo Electric Operation

-Entry Unit:
Extending Blade Peeler
Powered Entry Pinch Rolls
Drag Type Tension Pad

-Slitter Head:
Manual Side Guides
6.3" (160 mm) Diameter Arbors
Manual Top Arbor Adjust
Adjustable Fingers
Powered Entry Pinch Rolls
Manual Scrap Guides with Shute
20 HP DC Motor

-Scrap Baller:
DC Motor powered
Scrap Ball removal by Hydraulic Cylinder

-Pit Section:
Entry Centenary Section
Powered Carry Over Table

-Combination Tension Stand:
Powered Traverse to Carry Over Strip
Exit Centenary Section
Three (3) Separator Tooling Shafts
Two (2) Drag Boards
Tension Rolls (Rubber Coated)
25 HP DC Motor Braking System
Exit Passline Rolls (Rubber Coated)
Recoiler Feed Table

-Turret Recoiler:
8" Dia. and 24" Dia. Drums
Powered Horizontal Rotation
Hydraulic Pushoff (Base Mounted)
Powered Expansion (both drums)
Powered Gripper (24" Dia. Drum)
Holddown Arm
75 HP DC Motor

-Exit Coil Car:
Pit Type
Powered Lift and Traverse

-Exit Turnstile:
Two (2) Arms x 15,000# Each Arm @ 24" ID
One (1) Arm x 6,000# @ 8" ID
Powered Rotation

-Electrical Controls:
Main Operators Control Console
Auxiliary Operators Stations
AC & DC Control Cabinets
ABB Drive System (New in 2013)

-Slitter Tooling:
Hub and "Packed" Arbor Tooling
Carbide Knives
Steel Spacers
Rubbers
Misc. Separator Tooling
-Hydraulic System
-Spare Parts
-Drawings available of Line
Removed and in storage; Toledo, OH
Electrical cabinets in Holland, OH
1) 20' x 34" x 8' Ht
2) 7'6" x 19" x 7' Ht

according to the slitter slide chart
42” wide x 6.30” arbor diameter at 100% efficiency would be
capable of 13 cuts of .135” thick x 60,000psi shear strength material
107 hp at 260 fpm again 100% efficiency and .135” thick x 60,000psi shear strength 13 cuts max.
Raw calculations for the slitter head slitting and feed up
Slitting hp required to run 10 cuts of .135” thick at 260fpm 68hp (1.44 x 260 x .135 x .135 x 10)