Braner, Paxson Slitting Line 72 x 10 x 60,000 Lb

72 x 10 x 60,000 Lb PAXSON / BRANER Slitting Line


Materials: HRS, CRS, Galvanized
Coil I.D.: Entry - 20" to 24" (Nominal)
Exit - 20"
Coil O.D., Max.: Entry - 84"
Exit - TBD
Coil Width: 12" to 74" (Untrimmed)
Coil Weight: Entry - 60,000 Lb.
Exit - 40,000 Lb.

Thickness, Approx.: 0.075" to 0.250"

Shear, Max.: 50,000 PSI
Yield, Max.: 50,000 PSI

Line Direction: Left to Right
Mode of Operation: Pull Thru / Slitter Assist

Speed, Approx.: Slitter Assist - 0 to 300 / 360 FPM
Pull Thru - 300 FPM Bare Drum

Sample Cut Chart (Arbor Only), Mild Steel @ 50,000 PSI:

0.250" - (9) @ 72", (12) @ 60", (21) @ 48"
0.187" - (12) @ 72", (17) @ 60"
0.135" - (16) @ 72", (21) @ 60"

CONSISTING OF:
CINCINNATI Entry Coil Car:
Mast Type, Floor Mounted, Self-Contained Hydraulic
Unit, Powered Lift and Traverse, Cable Reel,
No Pendant Control

PAXSON Uncoiler:

Single Mandrel Type, Powered Expansion,
Holddown / Powered Snubber Roll with Banding Slots,
Wichita Water Cooled Brake (ATD 221), Slide Base,
Feedup Drive, No Water Cooler

CINCINNATI Entry Unit:

Extending Blade Type Peeler, Powered Entry Pinch
Rolls, Powered Side Guides

Provision for a Crop Shear (Not Available)

Coil Breaker:

Powered Entry Pinch Rolls, (3) Work Rolls in a
0.500" Configuration, Hydraulically Powered

PAXSON Stationary Slitter Base:

Powered Entry Pinch Rolls, 40 HP AC Feedup Motor
(1765 RPM), 159.8/1 Gear Reducer, 200 HP DC Motor
(1750 RPM, 500 Volts), SM-Cyclo Gear Reducer
(92.1 HP, 21/1)

(2) PAXSON Slitter Heads:

Crane Removable, 10" Diameter Arbors, Manual Outboard
Retraction, Powered Top Arbor Adjust

ROYALTON Pit Section:

Mounted to Tension Stand, Entry Passline Roll,
Carry Over Table

ROYALTON Tension Stand:

Drag Type, Separator Arm on "Swing-Out" Frame,
Internal Powered Pinch Rolls, 0.187" to 0.250" (Mild
Steel) Down Cut Type Crop Shear, Recoiler Feed Table

Recoiler:

Hydraulic Push-Off, Hydraulic Expansion and Gripper,
150 / 175 HP DC Motor (500 / 1600 RPM, 240 Volts),
28/1 (Approx.) Gear Reducer, Overarm Separator
(Needs to be attached to Recoiler)

47" W x 72" O.D. x 30,000 Lb. BRANER Exit Coil Car:

Mast Type, Floor Mounted, Self-Contained Hydraulic
Unit, Powered Lift and Traverse, No Pendant Control,
No Cable Reel

(2) BRANER Scrap Winders:

Automatic Scrap Dump, Level Wind, 14" x 45" OD
Bundle (Approx.)

Electrical Controls:

Main Operators Control Panel (Incomplete), Misc.
Control Consoles, AC/DC Control Cabinets
(Incomplete), (1) DC Drive for Recoiler (New)

Hydraulic System:

(1) 15 HP x 20 GPM HPU and (1) 15 HP x 15 GPM HPU

Tooling:

Shimless, Knives (New), Steel Spacers, Rubbers,
Separator Tooling